Experimental study on the influence of supply terminal shape on temperature, contaminant distributions and flow characteristics in impinging jet ventilation

Lee, Sungeun; Kobayashi, Tomohiro; Yamasawa, Haruna et al.

Building and Environment, 2026, 293, 114329

アクセス数:26件（2026-05-25 02:56 集計）

固定URL: https://hdl.handle.net/11094/104602

閲覧可能ファイル 

ファイル フォーマット 利用条件 サイズ 閲覧回数 利用開始日 説明 information
BuildEnviron_293_114329 pdf なし 11.3 MB 37 2026.04.27  
Creative Commons : 表示 - 非営利 - 改変禁止

論文情報

ファイル出力 EndNote Basic出力 Mendeley出力

タイトル
Experimental study on the influence of supply terminal shape on temperature, contaminant distributions and flow characteristics in impinging jet ventilation
著者
著者名
Lee, Sungeun
NRID
1000090580952 1000090580952
ORCID
0000-0003-4956-1274 0000-0003-4956-1274
researchmap permalink
tkoba_0151426 tkoba_0151426
Scopus Author ID
55724294200 55724294200
著者名
Kobayashi, Tomohiro
NRID
1000080982305 1000080982305
ORCID
0000-0002-1262-8781 0000-0002-1262-8781
researchmap permalink
yamasaswa_haruna yamasaswa_haruna
Scopus Author ID
57221740075 57221740075
著者名
Yamasawa, Haruna
著者名
Kida, Kentaro
キーワード等
Impinging jet ventilation (IJV)
Indoor environment
Jet characteristics
Supply terminal shape
Ventilation effectiveness
内容
Lee S., Kobayashi T., Yamasawa H., et al. Experimental study on the influence of supply terminal shape on temperature, contaminant distributions and flow characteristics in impinging jet ventilation. Building and Environment 293, 114329 (2026); https://doi.org/10.1016/j.buildenv.2026.114329.
抄録
Impinging jet ventilation (IJV) systems provide higher ventilation effectiveness in the occupied zone compared to traditional mixing ventilation systems. However, IJV system design requires careful consideration of parameters influencing the indoor environment, among which the supply terminal shape could be one of the important parameters. This study aims to investigate the impact of the IJV supply terminal shape on the indoor environment and the impinging jet characteristics. Full-scale experiments were conducted using three different slit-type supply terminals, measuring indoor temperature, CO₂ concentration assuming contaminants, and impinging jet velocity distribution. The experimental results indicated that under the low airflow rate conditions, the supply terminal shape had little impact on the indoor environment, whereas under the high airflow rate conditions, the heat and contaminant removal effectiveness showed a decreasing tendency with increasing the aspect ratio of the supply terminal. The stratification height of CO₂ concentration rose as the airflow rate increased as is well-known, and it was not affected by terminal shape at low supply flow rate conditions. However, when supply airflow rate is large, it was located lower as the aspect ratio of the terminal became higher. Analysis of impinging jet characteristics indicated that a lower aspect ratio of the supply terminal produced more diffusive airflows than the higher aspect ratio terminal. Also, the velocity of the airflow reaching a heating element was higher at the higher aspect ratio conditions. These variations in jet characteristics could affect the indoor environment by changing air distribution patterns and plume flow rate.
出版者
Elsevier Ltd
収録物名
Building and Environment
巻(号)
293
ページ
114329
刊行年月
2026-02-10
言語
英語
ハンドルURL
https://hdl.handle.net/11094/104602
PISSN
03601323
関連情報 (isIdenticalTo)
DOI (出版社版)
https://doi.org/10.1016/j.buildenv.2026.114329
アクセス権
open access
権利情報
This article is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
出版タイプ
Version of Record
カテゴリ
学術雑誌論文 Journal Article