Specific Strength of Sandwich-Structured Composite of Open-Cell Metallic Foam/Resin Joined by Friction Stir Incremental Forming

Matsumoto, Ryo; Sakaguchi, Harutaka; Otsu, Masaaki; Utsunomiya, Hiroshi

doi:https://doi.org/10.1007/978-981-19-3307-3_31

Specific Strength of Sandwich-Structured Composite of Open-Cell Metallic Foam/Resin Joined by Friction Stir Incremental Forming

Matsumoto, Ryo; Sakaguchi, Harutaka; Otsu, Masaaki et al.

Lecture Notes in Mechanical Engineering, 2022, 343-349

アクセス数:519件（2025-08-28 17:26 集計）

固定URL: https://hdl.handle.net/11094/94001

閲覧可能ファイル

ファイル	フォーマット	利用条件	サイズ	閲覧回数	利用開始日	説明	information
LectNotesMechEng_343	pdf	なし	393 KB	60	2024.02.26

論文情報

ファイル出力 EndNote Basic出力 Mendeley出力

タイトル	Specific Strength of Sandwich-Structured Composite of Open-Cell Metallic Foam/Resin Joined by Friction Stir Incremental Forming
著者	NRID 1000050362645 1000050362645 ORCID 0000-0002-4477-2139 0000-0002-4477-2139 researchmap permalink ryo-matsumoto ryo-matsumoto Scopus Author ID 35512063000 35512063000 著者名 Matsumoto, Ryo
	著者名 Sakaguchi, Harutaka
	NRID 1000020304032 1000020304032 著者名 Otsu, Masaaki
	NRID 1000080252584 1000080252584 researchmap permalink read0042799 read0042799 Scopus Author ID 7102139699 7102139699 著者名 Utsunomiya, Hiroshi
キーワード等	Composite structure
	Nickel foam
	Plastic joining
	Polymethyl methacrylate
	Strength-mass relationship
内容	This version of the article has been accepted for publication, after peer review (when applicable) and is subject to Springer Nature’s AM terms of use, but is not the Version of Record and does not reflect post-acceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/978-981-19-3307-3_31
抄録	The compressive deformation behavior of an open-cell nickel foam joined with polymethyl methacrylate (PMMA) sheets by friction stir incremental forming (FSIF) process was investigated with uniaxial compression test. The sheet was joined on each side face of the foam for fabrication of the foam/sheet composite for uniaxial compression test. In FSIF process, the bottom of the sheet was mechanically interlocked to the surface pores of the foam by plastic flow of the frictionally heated sheet. In uniaxial compression test, the cubic foam/sheet composite was compressed with an initial strain rate of 1.0 × 10−3 s−1. The compressive specific strength of the foam/sheet composite was approximately 30 times higher than that of the foam. This was due to not only high specific strength of the sheet but also the sandwich structure of the foam/sheet composite.
出版者	Springer Science and Business Media Deutschland GmbH
収録物名	Lecture Notes in Mechanical Engineering
ページ	343-349
刊行年月	2022-10-06
言語	英語
ハンドルURL	https://hdl.handle.net/11094/94001
PISSN	21954356
eISSN	21954364
関連情報 (isVersionOf)	DOI (出版社版) https://doi.org/10.1007/978-981-19-3307-3_31
アクセス権	open access
出版タイプ	Accepted Manuscript
カテゴリ	会議発表論文 Conference Paper

資源タイプ	会議発表論文
ローカル資源タイプ	会議発表論文
DCMI資源タイプ	text
DCTERMS.bibliographicCitation	Lecture Notes in Mechanical Engineering. 2022, p. 343-349
DC.title	Specific Strength of Sandwich-Structured Composite of Open-Cell Metallic Foam/Resin Joined by Friction Stir Incremental Forming
DC.creator	Matsumoto, Ryo
	Sakaguchi, Harutaka
	Otsu, Masaaki
	Utsunomiya, Hiroshi
DC.publisher	Springer Science and Business Media Deutschland GmbH
DC.language' scheme='DCTERMS.RFC1766	英語
DC.type' scheme='DCTERMS.DCMIType	text
DCTERMS.issued' scheme='DCTERMS.W3CDTF	2022-10-06
DC.identifier	https://doi.org/10.1007/978-981-19-3307-3_31
DC.subject	Composite structure
	Nickel foam
	Plastic joining
	Polymethyl methacrylate
	Strength-mass relationship
DC.description	This version of the article has been accepted for publication, after peer review (when applicable) and is subject to Springer Nature’s AM terms of use, but is not the Version of Record and does not reflect post-acceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/978-981-19-3307-3_31
DCTERMS.abstract	The compressive deformation behavior of an open-cell nickel foam joined with polymethyl methacrylate (PMMA) sheets by friction stir incremental forming (FSIF) process was investigated with uniaxial compression test. The sheet was joined on each side face of the foam for fabrication of the foam/sheet composite for uniaxial compression test. In FSIF process, the bottom of the sheet was mechanically interlocked to the surface pores of the foam by plastic flow of the frictionally heated sheet. In uniaxial compression test, the cubic foam/sheet composite was compressed with an initial strain rate of 1.0 × 10−3 s−1. The compressive specific strength of the foam/sheet composite was approximately 30 times higher than that of the foam. This was due to not only high specific strength of the sheet but also the sandwich structure of the foam/sheet composite.
DC.format	94001
citation_title	Specific Strength of Sandwich-Structured Composite of Open-Cell Metallic Foam/Resin Joined by Friction Stir Incremental Forming
citation_author	Matsumoto, Ryo
	Sakaguchi, Harutaka
	Otsu, Masaaki
	Utsunomiya, Hiroshi
citation_publisher	Springer Science and Business Media Deutschland GmbH
citation_language	英語
citation_date	2022-10-06
citation_journal_title	Lecture Notes in Mechanical Engineering
citation_firstpage	343
citation_lastpage	349
citation_doi	https://doi.org/10.1007/978-981-19-3307-3_31
citation_public_url	https://hdl.handle.net/11094/94001

Specific Strength of Sandwich-Structured Composite of Open-Cell Metallic Foam/Resin Joined by Friction Stir Incremental Forming

閲覧可能ファイル

論文情報

論文詳細を表示