Reduction in Barreling of Hollow Cylinder by Combination of Axial Compression and Circumferential Torsion in Upsetting with Conical Dies

Matsumoto, Ryo; Tanaka, Sotaro; Utsunomiya, Hiroshi

doi:https://doi.org/10.1007/978-3-031-41023-9_3

Reduction in Barreling of Hollow Cylinder by Combination of Axial Compression and Circumferential Torsion in Upsetting with Conical Dies

Matsumoto, Ryo; Tanaka, Sotaro; Utsunomiya, Hiroshi

Lecture Notes in Mechanical Engineering, 2023, 27-35

Number of Access:594（2025-10-05 11:32 Counts）

Identifier to cite or link to this item: https://hdl.handle.net/11094/94002

Link to primary information

File	Format	Terms of use	Size	Views	Date.Available	Description	information
LectNotesMechEng_27	pdf	None	268 KB	28	2024.08.23

Item Information

Output File Export EndNote Basic Export Mendeley

Title	Reduction in Barreling of Hollow Cylinder by Combination of Axial Compression and Circumferential Torsion in Upsetting with Conical Dies
Creator	NRID 1000050362645 1000050362645 ORCID 0000-0002-4477-2139 0000-0002-4477-2139 researchmap permalink ryo-matsumoto ryo-matsumoto Scopus Author ID 35512063000 35512063000 CreatorName Matsumoto, Ryo
	CreatorName Tanaka, Sotaro
	NRID 1000080252584 1000080252584 researchmap permalink read0042799 read0042799 Scopus Author ID 7102139699 7102139699 CreatorName Utsunomiya, Hiroshi
Subject	Barreling
	Forging
	Hollow cylinder
	Plastic flow
	Stress superposition
	Torsion
Description	This version of the article has been accepted for publication, after peer review (when applicable) and is subject to Springer Nature’s AM terms of use, but is not the Version of Record and does not reflect post-acceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/978-3-031-41023-9_3
Abstract	To reduce barreling of hollow cylinder in upsetting, circumferential one-way torsion with twist/compression speed of 0–12°/mm was combined with axial compression in upsetting. Due to combination of compression and torsion, the plastic flow of the workpiece was enhanced in the outer radial direction on the die–workpiece interface. Barreling was reduced by combining compression and torsion with lower than 5°/mm, whereas hourglass deformation occurred by combining compression and torsion with higher than 6°/mm. The workpiece was successfully deformed without barreling and hourglass deformation (0.97 < fraction of diameters of height center/end face < 1.01) by interrupting the die rotation in upsetting with reduction in height of lower than 50%.
Publisher	Springer Science and Business Media Deutschland GmbH
Source Title	Lecture Notes in Mechanical Engineering
Page	27-35
Date of Issued	2023-08-23
Language	English
Handle URL	https://hdl.handle.net/11094/94002
PISSN	21954356
eISSN	21954364
Relation.isVersionOf	DOI (Publisher Version) https://doi.org/10.1007/978-3-031-41023-9_3
Access Rights	open access
oaire:version	Accepted Manuscript
Category	会議発表論文 Conference Paper

Resource Type	conference paper
Local Type	Conference Paper
DCMI Type	Text
DCTERMS.bibliographicCitation	Lecture Notes in Mechanical Engineering. 2023, p. 27-35
DC.title	Reduction in Barreling of Hollow Cylinder by Combination of Axial Compression and Circumferential Torsion in Upsetting with Conical Dies
DC.creator	Matsumoto, Ryo
	Tanaka, Sotaro
	Utsunomiya, Hiroshi
DC.publisher	Springer Science and Business Media Deutschland GmbH
DC.language' scheme='DCTERMS.RFC1766	English
DC.type' scheme='DCTERMS.DCMIType	Text
DCTERMS.issued' scheme='DCTERMS.W3CDTF	2023-08-23
DC.identifier	https://doi.org/10.1007/978-3-031-41023-9_3
DC.subject	Barreling
	Forging
	Hollow cylinder
	Plastic flow
	Stress superposition
	Torsion
DC.description	This version of the article has been accepted for publication, after peer review (when applicable) and is subject to Springer Nature’s AM terms of use, but is not the Version of Record and does not reflect post-acceptance improvements, or any corrections. The Version of Record is available online at: https://doi.org/10.1007/978-3-031-41023-9_3
DCTERMS.abstract	To reduce barreling of hollow cylinder in upsetting, circumferential one-way torsion with twist/compression speed of 0–12°/mm was combined with axial compression in upsetting. Due to combination of compression and torsion, the plastic flow of the workpiece was enhanced in the outer radial direction on the die–workpiece interface. Barreling was reduced by combining compression and torsion with lower than 5°/mm, whereas hourglass deformation occurred by combining compression and torsion with higher than 6°/mm. The workpiece was successfully deformed without barreling and hourglass deformation (0.97 < fraction of diameters of height center/end face < 1.01) by interrupting the die rotation in upsetting with reduction in height of lower than 50%.
DC.format	94002
citation_title	Reduction in Barreling of Hollow Cylinder by Combination of Axial Compression and Circumferential Torsion in Upsetting with Conical Dies
citation_author	Matsumoto, Ryo
	Tanaka, Sotaro
	Utsunomiya, Hiroshi
citation_publisher	Springer Science and Business Media Deutschland GmbH
citation_language	English
citation_date	2023-08-23
citation_journal_title	Lecture Notes in Mechanical Engineering
citation_firstpage	27
citation_lastpage	35
citation_doi	https://doi.org/10.1007/978-3-031-41023-9_3
citation_public_url	https://hdl.handle.net/11094/94002

Reduction in Barreling of Hollow Cylinder by Combination of Axial Compression and Circumferential Torsion in Upsetting with Conical Dies

Link to primary information

Item Information

Show details